Combi 50 - 56 system package I.

Combi 50 - 56 system package I.
4 054

In case of buying Celsius system package we insure 5 years extendable guarantee*!


Celsius Combi 50 - 56 system package I. content:

  • Celsius Combi 50 - 56 boiler
  • Pellet adapter door for connection pellet burner
  • Celsius boiler anticondensing F-package
  • Celsius safety heat exchanger
  • 3-way motorized zone valve 1"
  • System controller (Euroster 813)
  • Celsius insulated puffer tank 1500l


Please look at our system's offer for this system with hot domestic fresh water modul!

Clicking this picture you can inform the contents of system package:


*(It need to check the boiler condition annually and every non eletric part annually.)

Celsius Combi boiler

With pellet adapter door


The Celsius Combi Boiler is our most up to date boiler.

Celsius Combi boilers were developed to operate with either dry wood or wood pellet (DIN+ quality, 6 mm diameter thick). Its structure is similar to that of a traditional wood burning boiler, however, its operation is a lot more economical with the use of highly efficient equipment. The boiler requires minimum maintenance and will continue to meet your heating requirements over its long lifetime. The boiler can be connected to any kind of central heating system, from radiator to floor heating.


The Celsius Combi Boiler with Wood Pellet burner is efficient and convenient because of:

  • Automatic turn on and turn off switching
  • Keeping fire and modulation (5 performance levels)
  • Increased savings due to possibility of 4 different pellet quality parameters.
  • Faster cleaning


These boilers are suitable for burning wood and in auto mode Wood Pellets may also be used. Thanks to its special design the boiler can utilize both fuels with outstanding efficiency. Celsius boilers are suitable for gravity or pump controlled heating systems for family houses, workshops, various farm houses, agricultural halls, institutions and greenhouses. Celsius solid fuel burning boilers have different models which are sized by heat output to meet your individual requirements.



  • Fire grates (grills) 
  • Wooden pellet burner adapter door
  • Filling/draining trap







Height of boiler


Width of boiler


Depth of boiler


Boiler body


Exterior cover


Return water connection


Filling/draining tap connection


Upper door


Ash pan


Firing door (wood burning)


Pellet burner adapter door


Ash removal door (primary draught regulator)


Door opening handle




Heat exchangers


Grate (grill)


Safety valve or pressure guage


Uptake connection


Forward water connection


Thermometer connection


Automatic draugh regulator connection




Modul Combi 50 - 56
Firing door size (mm) 310*385
Maximum heat output (kW) wood/pellet 56/51
Heating-system dependant heatable air-space(m3) 800-1500
Fuel-dependant efficiency (%) wood/pellet 88/92
Heating water connection (") 2
Uptake connection (mm) 160
Height (mm) 1160
Width (mm) 755
Depth (mm) 775
Weight (kg) 350
Water volume (l) 130
Max. operating pressure (bar) 2
Max. operating temperature (°C) 90
Test pressure (bar) 4
Draught demand (g/s) 40,3
Firebox size (mm) (height*width*depth) 460*560*600




Celsius safety heat exchanger



It protects the boiler and environment if the boiler is overloaded and the heating system can not heat distribute (There is not buffer tank and irregular usage).


Content of equipment:

  • Celsius safety heat exchanger
  • Vent valve
  • Thermostatic security valve (opening temperature 98°C)
  • Pressure security valve (2bar)


Applicable to the following boiler types:
Celsius classic, Celsius C and Celsius Combi boiler




F-Celsius anticondensing package to 65 kW


Kazánvédő csomag



Boiler protection unit to prevent condensation
Condensation is an often experienced phenomenon during the use of the solid fuel boilers which is always harmful, will cause lifespan shorthening, efficiency drop, and higher heating costs.


Content of equipment:

  • circulation pump (Grundfos UPM3 25-70 Hybrid)
  • pump hollander (ball tap) 1 piece
  • Celsius boiler protection valve
  • to 65kW KVS 7,2


Principle of operation:



1. Starting the system (heating the boiler)
After the launching of the boiler, the thermic valve is fully closed towards the user (gate A) and remains in this condition until the fluid is warmed up by the heating source, gets the opening temperature of the thermic valve (corresponding to the calibration value, f.i. 55°C). During this step the fluid sent by the boiler fully recycles through the by-pass (gate B) so the boiler temperature rises very quickly.



2. Loading the system (heating the tank)
Reaching the opening temperature (f.i. 55C), gate A proportionally starts to open while gate B proportionally starts to close. The boiler temperature slowly rises, giving energy to the end user, but the returning temperature will not decrease below the calibrated temperature (f.i. 55°C).



3. System operation
Starting from point 2, the flow temperature progressively increases to fully open gate valve A. This will correspondingly close gate valve B. This happens at approximately circa 10k higher than the calibration or opening temperature (therefore in this example at 65c). Now the installation is fully operational the supply fluid temperature can increase to set value.
For example, if the valve opening temperature is 55°C, then it is totally opened in the direction of A → AB in case of +10°C.




Celsius insulated buffer tank



Celsius buffer tanks:

To maximise the efficiency of a solid fuel heating system a buffer tank should be installed. When the boiler has produced energy to satisfy the heat demand, excess energy produced by fuel in the combustion chamber can be captured and stored in the buffer tank. The exception to this is when using wood pellets, where the pellet burner will automatically stop when the heat demand has been satisfied.
When the heating system have surplus heat ,the buffer tank stores it, therefore the wood boiler doesen't need an automatic draft regulator which ruins the burning efficiency.


Advantages of Celsius insulated buffer tank:

  • High quality insulation (C energy rating, EU complaint)
  • More economical burning
  • Lower pollutant emissions
  • Aesthetic design
  • Guaranteed continuous heating (for example: It can heat all night)
  • Hot domestic water modul can be connected



buffer tank





Motorized 3-way zone valve



Motorized 3-way zone valve with spring return for closed hydraulic systems.


Technical features:

  • Area of use: heating, conditionning and solar thermal (glycol max. 50%).
  • Power supply 230 VAC, 50Hz, absorbed power: 6W
  • Protection IP22
  • Nominal pressure PN10
  • Room temperature Max. 60°C
  • Fluid temperature: 5÷120°C; short time: 150°C;
  • Nominal opening time: 20 s. Springclosing: 6 s.
  • Kvs value 12,6
  • Without power AB->B
  • Weight 1,3 kg/piece





Euroster 813 controller



Operating principle:
The EUROSTER 813 control unit is a universal microprocessor controller with graphical display. The controller is responsible for the pump to operate on the basis of the difference between the set temperatures. It is possible to set up in the control an automatic disinfection function.


The control is responsible to turn on the pump on the basis of the difference between the set temperatures to ensure that the container is warmed by only the surplus heat, thus making energy savings.
The controller has a variety of automatic emergency circuit options.


You can set the emergency value of solar ebullience. There's an automatic vacation mode available, which takes care of cooling the storage to the set value, overheated by the solar system. This mode is important, if the storage is not used on a daily basis and ebullience of the solar panel will be induced. The keyboard of the control unit is lockable in the purpose of protection of your set parameters, which can cause an error.


The controller has a security sensor testing, if sensor sings, it will automatically trigger the pumps, preventing the ebullience. The controller has a sensor calibration mode, which allows you to avoid false temperature measurement by the long lines.


Treatment of controller
The graphics display of the EUROSTER 813 controller makes it easy to set up the controller. The options of setting the controller:
- Pressing the +/- buttons at the same time you can reach the menu.
- Pressing the -/ok buttons at the same time you can lock the keyboard.
- Pressing the +/ok buttons at the same time you can reach the manual mode, pressing the /+ button you can select the manually accessible devices.


After entering the menu you can set the following values:

  • time
  • disinfection (on/off)
  • modes
  • maximum emergency starting temperature of collector or boiler
  • minimal starting temperature of pump
  • maximum temperature of storage
  • starting and shutdown temperature of solar delta T
  • temperature of storage/hysteresis
  • calibration of solar sensor
  • calibration of storage sensor


Controller can be applied to:
In the case of Vacuum-tube control plane collector, mixed-fired boilers and buffers.
The pump must not be interrupted by other equipment!





Operating voltage

230V, 50Hz

Rated vattage


Output load of circuit pump


Emergency starting temp


Min. starting temperature of pump


Storage max. temperature


Delta T pump starting (on)


Delta T pump shutdown


Storage temperature


Storage hysteresis








Cables and sensors of E 813 controller:



Válasszon teljesítményt (kW)